? phoenix contact - 02/2007 103153_00_en interface plc accessories data sheet description plc-esk power terminal block the 9 mm plc-esk gy power terminal block is the same shape as the plc interface modules. it is used to supply the bridging potentials. it s nominal current is 32 a. for currents 6 a, the power can be supplied directly at the connection terminal blocks of one of the connected plc interface modules. fbst plug-in bridges the colored, insulated fbst plug-in bridges reduce wiring time for the plc interface modules by up to 70% in comparison with conventionally wired relay modules. 2-pos. fbst 6 single plug-in bridges are ideal for bridging a smaller number of modules and total currents 6 a. for a circuit supplied from both sides, they offer the advantage that the circuit can be opened at any point, while allowing all the other modules to continue being supplied at the same time. if a plc-atp insulating plate is to be bypassed with single plug-in bridges, the fbst 8 2-pos. plug-in bridge must be used. the fbst 14 2-pos. plug-in bridge connects adjacent connections on a 14 mm plc interface module. in this way, contacts can be connected in series or in parallel without additional wiring. 500 mm long fbst 500 continuous plug-in bridges can be used to bridge up to 80 modules quickly and easily at a time. plc-atp insulating plate the plc-atp insulating plate should always be installed at the start and end of every terminal strip. in addition to the visual separat ion of function blocks, it is also necessary in some cases to install the insulating plate between adjacent plc interface modules, e.g., when three phases (l1, l2, l3) are used on the contact side of the plc interface modules. plc-atp has prescored break-out points at the bridging positions, so that individual bridges can be passed through if necessary. plc-bp feed-through bridge instead of a relay or solid-st ate relay, the plc-bp (a1-14) passive feed-through bridge can be inserted in the basic terminal block of the plc interface series. this enables a passive connection to be established between terminal points a1 and 14. plc-v8 adapter the plc-v8 adapter can be used to connect both 6.2 mm and 14 mm plc interface modules quickly and easily to the varioface system cabling (see interface catalog). make sure you always use t he latest documentation. it can be downloaded at www.download.phoenixcontact.com . a conversion table is available on the internet at www.download.phoenixcontac t.com/general/7000_en_00.pdf . this data sheet is valid for all products listed on the following page: accessories for the pl c interface series
plc accessories 103153_00_en phoenix contact 2 zb 6 zack marker strip the zb marker system provides logical and clear identification of the modular terminal blocks and interface modules. multipartite zb strips can be conveniently split at any point. they are available with horizontal and vertical labeling (see clipline catalog). other pitches and labels are available on request. unprinted zb strips can be labeled individually using a plotter or by hand. ordering data zack marker strip description type order no. pcs./pck. zack marker strip, unprinted: 10-section, for individual labeling with tml (ex9,5)r tr, x-pen or cms-p1 plotter, each pack provides enough strips to label 100 plc interface modules as above, but large pack; each pack provides enough strips to label 1000 plc interface modules zb 6: unbedruckt zb 6/wh-100: unbedruckt 1051003 5060935 10 100 zack marker strip, printed horizontally: 1 10-section, with consecutive numbers 1 ten identically labeled strips make up one unit pack (pcs./pck.). 1 - 10 11 - 20 ... 991 - 1000 zb 6, lgs: fortl. zahlen zb 6, lgs: 1-10 zb 6, lgs: 11-20 ... zb 6, lgs: 991-1000 1051032 10 zack marker strip, printed horizontally: 1 9-section, with numbers 1 - 9 1 - 9 zb 6, lgs: 1-9 1051126 10 zack marker strip, printed horizontally: 1 10-section, with identical numbers 1/1/1 2/2/2 ... 100/100/100 zb 6, lgs: gleiche zahlen zb 6, lgs: 1 zb 6, lgs: 2 ... zb 6, lgs: 100 1051032 10 zack marker strip, printed horizontally: 1 10-section l1, l2, l3, n, pe, l1, l2, l3, n, pe u, v, w, n, 6 , u, v, w, n, 6 zb 6, lgs: l1-n, pe zb 6, lgs: u-n 1051414 1051430 10 10 zack marker strip, printed vertically: 1 10-section, with consecutive numbers 1 - 10 11 - 20 ... 991 - 1000 zb 6, qr: fortl. zahlen zb 6, qr: 1-10 zb 6, qr: 11-20 ... zb 6, qr: 991-1000 1051029 10 zack marker strip, printed vertically: 1 10-section, with identical numbers 1/1/1 2/2/2 ... 100/100/100 zb 6, qr: gleiche zahlen zb 6, qr: 1 zb 6, qr: 2 ... zb 6, qr: 100 1051045 10 zack marker strip, printed vertically: 1 10-section, with plc input numbers, e.g., i 0.0 to i 0.7 (up to i 127.7, maximum) zb 6, qr: sps eingang... 2 2 specify desired labeling when placing an order. 1051456 10 zack marker strip, printed vertically: 1 10-section, with plc output numbers e.g., o 0.0 to o 0.7 (up to o 127.7, maximum) zb 6, qr: sps ausgang... 2 1051443 10 zack marker strip with special labeling: 10-section, can be separated, labeled according to customer requirements zb 6: so/cms... 3 3 specify desired labeling and color when placing an order. 1050499 1 horizontal labeling (lgs): vertical labeling (qr): 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10
plc accessories 103153_00_en 3 phoenix contact gmbh & co. kg ? 32823 blomberg ? germany phone: +49 - 52 35 - 30 0 ? fax: +49 - 52 35 - 34 12 00 www.phoenixcontact.com technical data ? phoenix contact 02/2007 power terminal block description type order no. pcs./pck. power terminal block, to supply up to four potentials, same shape as the plc interface series gray plc esk gy 2966508 5 plug-in bridges description type order no. pcs./pck. continuous plug-in bridge, 500 mm long, insulated, can be cut to any length, for potential distribution with plc..., i max = 32 a red blue gray fbst 500-plc rd fbst 500-plc bu fbst 500-plc gy 2966786 2966692 2966838 20 20 20 plug-in bridge, 2-pos., 6 mm long, insulated, for potential distribution with plc..., i max = 6 a red blue gray fbst 6-plc rd fbst 6-plc bu fbst 6-plc gy 2966236 2966812 2966825 50 50 50 plug-in bridge, 2-pos., 8 mm long, insulated, for potential distribution with insulating plate gray fbst 8-plc gy 2967688 50 plug-in bridge, 2-pos., 14 mm long, insulated, for potential distribution black fbst 14-plc bk 2967691 50 insulating plate description type order no. pcs./pck. insulating plate, 2 mm thick, to be installed at the start and end of every plc terminal strip. for the visual separation of groups, safe isolation of different voltages from adjacent plc interface modules according to din en 50178/vde 0160, isolation of adjacent bridges with different potentials, isolation of plc interface modules for voltages greater than 250 v. color: black plc atp bk 2966841 25 feed-through bridge description type order no. pcs./pck. passive feed-through bridge, can be inserted instead of a relay or solid-state relay, bridges terminal points a1 and 14 black plc bp (a1-a14) 2980283 1 screwdriver description type order no. pcs./pck. bladed type screwdriver, blade: 0.6 x 3.5 x 100 mm, length 180 mm szf 1-0,6x3,5 1204517 10 plc-esk power terminal block nominal input voltage 1 250 v ac, maximum total current 32 a, maximum connection type screw connection conductor cross section (solid and stranded) 0.2 mm 2 ... 4 mm 2 stripping length 10 mm dimensions (w x h x d) 9 mm x 94 mm x 80 mm housing material polyamide pa, color: gray 1 the plc-atp bk insulating plate must be installed for voltages greater than 250 v (l1, l2, l3) between the same terminal points on adjacent modules (see "insulating plate"). fbst 8-plc... or fbst 500... is then used for potential bridging.
|
